View CEP-1153_4993119.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Part No: CEP-1153 Description: piezo audio transducer
Date: 9/22/2006 Unit: mm Page No: 1 of 4
Specifications
Operating voltage Current consumption Sound pressure level Electrostatic capacity Operating tempurature Storage tempurature Dimensions Weight Material Terminal RoHS 30 Vp-p max. 7 mA max. 82 db min. 14,000 pF 30% -30 ~ +105 C -40 ~ +105 C o17.0 x H7.6 mm 3.4 g max. PBT+15% GF (Black) Pin type (Au Plating) yes at 10 Vp-p, square wave, 4.0 KHz at 10 cm / 10 Vp-p, square wave, 4.0 KHz at 1 KHz / 1 V
Appearance Drawing
Tolerance: 0.5
Phone: 800.275.4899
Fax: 503.612.2381
www.cui.com
20050 SW 112th Ave.
Tualatin, OR 97062
Part No: CEP-1153 Description: piezo audio transducer
Date: 9/22/2006 Unit: mm Page No: 2 of 4
Typical Frequency Response Curve
Measurement Method
S.P.L. Measuring Circuit Input Signal: 10 Vp-p, 4.0 KHz, Square Wave Mic: RION S.P.L. meter UC30 or equivalent S.G.: Hewlett Packard 33120A Function Generator or equivalent
Phone: 800.275.4899
Fax: 503.612.2381
www.cui.com
20050 SW 112th Ave.
Tualatin, OR 97062
Part No: CEP-1153 Description: piezo audio transducer
Date: 9/22/2006 Unit: mm Page No: 3 of 4
Mechanical Characteristics
Item Solderability Evaluation Standard Test Condition 90% min. of the lead terminals Lead terminals are immersed in rosin for will be wet with solder. 5 seconds and then immersed in solder bath (Except the edge of the terminal) of 270 5C for 3 1 seconds. Lead terminals are immersed up to 1.5mm from No interference in operation. buzzer's body in solder bath of 300 5C for 3 0.5 seconds or 260 5C for 10 1 seconds. No damage or cutting off. For 10 seconds, the force of 9.8N (1.0kg) is applied to each terminal in axial direction. The value of oscillation The buzzer shall be measured after applying frequency/current consumption a vibration amplitude of 1.5 mm with 10 to should be 10% of the initial 55 Hz band of vibration frequency to each of measurements. The SPL should the 3 perpendicular directions for 2 hours. be within 10dB compared with The part will be dropped from a height of the initial measurement. 75 cm onto a 40 mm thick wooden board 3 times in 3 axes (X, Y, Z) for a total of 9 drops.
Soldering Heat Resistance
Terminal Mechanical Strength Vibration
Drop Test
Environment Test
Item High temp. test Low temp. test Humidity test Temp. cycle test Test Condition After being placed in a chamber at +105C for 240 hours. After being placed in a chamber at -40C for 240 hours. After being placed in a chamber at +40C and 905% relative humidity for 240 hours. The part shall be subjected to 5 cycles. One cycle will consist of: Evaluation Standard
The buzzer will be measured after being placed at +25C for 4 hours. The value of the oscillation frequency/current consumption should be 10% compared to the initial measurements. The SPL should be within 10dB compared to the initial measurements.
Phone: 800.275.4899
Fax: 503.612.2381
www.cui.com
20050 SW 112th Ave.
Tualatin, OR 97062
Part No: CEP-1153 Description: piezo audio transducer
Date: 9/22/2006 Unit: mm Page No: 4 of 4
Reliability Test
Item Operating (Life Test) Test Condition 1. Continuous life test: The part will be subjected to 48 hours of continuous operation at +90C with rated voltage applied. 2. Intermittent life test: A duty cycle of 1 minute on, 1 minute off, a minimum of 5,000 times at room temp (+25 2C) with rated voltage applied. Evaluation Standard The buzzer will be measured after being placed at +25C for 4 hours. The value of the oscillation frequency/current consumption should be 10% compared to the initial measurements. The SPL should be within 10dB compared to the initial measurements.
Test Conditions
Standard Test Condition Judgement Test Condition a) Tempurature: +5 ~ +35C a) Tempurature: +25 2C b) Humidity: 45 - 85% b) Humidity: 60 - 70% c) Pressure: 860-1060 mbar c) Pressure: 860-1060 mbar
Packaging
Phone: 800.275.4899
Fax: 503.612.2381
www.cui.com
20050 SW 112th Ave.
Tualatin, OR 97062

▲Up To Search▲

Price & Availability of CEP-1153

	To Download CEP-1153 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .